+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
14.1.2. Measuring devices
14.1.3. Technology of measurements
14.1.4. Checks of electric equipment
14.1.5. Sound signal
14.1.6. Replacements of safety locks
+ 14.1.7. Rechargeable battery
+ 14.1.8. Generator
+ 14.1.9. Starter
14.1.10. Traction relay
- 14.1.11. System of lighting
188.8.131.52. Lamps of passing, driving and fog beam
184.108.40.206. A lamp in a forward lamp of the index of turn
220.127.116.11. A lamp in a back lamp
18.104.22.168. A lamp in a lamp of illumination of registration plate
22.214.171.124. A plafond in salon
126.96.36.199. Lamp of the index of turn
- 188.8.131.52. Headlight
184.108.40.206.1. Adjustment of headlights
220.127.116.11. Back lamp
14.1.14. Glow lamps on the dashboard
14.1.15. Light switch
14.1.16. Radio receiver
+ 14.1.17. Antenna
+ 14.1.19. Rubber brushes of screen wipers
14.1.20. Windscreen washer jets
14.1.21. The washing nozzles of headlights
14.1.22. Screen wiper and its engine
14.1.23. Protect the car
14.1.24. Anticreeping "immunodeficiency"
14.1.25. Why headlights grow dull
+ 14.2. Electrical circuitries
|14. The plug for a lamp of the index of turn
30. The plug for lighting
32. A hose to the device for cleaning of the lens of a headlight (a faroochistitel or a faroomyvatel)
| 33. Pneumatic pipeline
M6/2x1, M6/3x1. Shtekker of the screen wiper engine to the left / to the right
|22. Nut 23. Washer
24. Screen wiper neck lever
25. Protection cover
| E1, E2. Headlights, at the left / on the right
M6/2, M6/3. Engines of screen wipers of headlights at the left/on the right
M6/2x1, M6/3x1. Shtekkera of engines of screen wipers at the left / on the right
| PERFORMANCE ORDER
| 1. Remove a lamp of the index of turn.
| 2. Remove from a headlight electric wires and the pneumatic pipeline for adjustment on height.
| 3. If is available, remove the screen wiper brush lever (24) headlights. For this purpose cast away the protection cover up, unscrew a nut (22) and remove it together with a washer (23).
|4. Depending on equipment, unscrew a cross-piece or side protection covers in a zone of fastening of headlights.
| 5. Unscrew two screws (26) and unhook the protection cover (25) under a headlight.
|6. Unscrew screws (27-29) and carefully extend a headlight forward. Close the shock-absorber a rag not to scratch it.
|7. If is available, remove a hose to the device for cleaning of the lens of a headlight.
|8. If it is necessary to take out the lens of an optical element of a headlight, remove rubber consolidation. Take from spring clips above and below two supporting earrings (38). Remove the lens of an optical element (9) together with consolidation (21).
| PERFORMANCE ORDER
| 1. If it is removed, insert the lens of an optical element of a headlight into the case and at the same time press it until the supporting earrings above and below are not recorded with click.
| 2. In advance check consolidation for lack of porosity, if necessary replace it.
| 3. Further installation is carried out in the sequence, the return dismantling.
|4. After completion of assembly adjust headlights in specialized auto repair shop.