Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
   14.1.2. Measuring devices
   14.1.3. Technology of measurements
   14.1.4. Checks of electric equipment
   14.1.5. Sound signal
   14.1.6. Replacements of safety locks
   + 14.1.7. Rechargeable battery
   + 14.1.8. Generator
   + 14.1.9. Starter
   14.1.10. Traction relay
   + 14.1.11. System of lighting
   14.1.12. Devices
   14.1.13. Dashboard
   14.1.14. Glow lamps on the dashboard
   14.1.15. Light switch
   14.1.16. Radio receiver
   + 14.1.17. Antenna
   14.1.18. Loudspeakers
   + 14.1.19. Rubber brushes of screen wipers
   14.1.20. Windscreen washer jets
   14.1.21. The washing nozzles of headlights
   14.1.22. Screen wiper and its engine
   14.1.23. Protect the car
   14.1.24. Anticreeping "immunodeficiency"
   14.1.25. Why headlights grow dull
   14.1.26. Galogenka
+ 14.2. Electrical circuitries





Вес задвижки стальной ду.

14.1.16. Radio receiver

GENERAL INFORMATION

 
51. Dismantling keys A2. Radio receiver

Removal


Prevention

The receivers which both are serially installed, and acquired in trade have code number. It protects the receiver from unauthorized use. After turning on of the radio receiver it is necessary to enter code number according to the maintenance instruction, otherwise it cannot be included. If the radio receiver is coded, then define a radio code before a detachment of wires from plugs of the rechargeable battery or its removal. If the code is unknown, then only the manufacturer can put the automobile receiver into operation. Individual code number is specified in the passport of the radio receiver. This passport should not be stored in the car.


PERFORMANCE ORDER
1. Disconnect a weight(s) wire from the plug of the rechargeable battery.
Prevention

At the same time the anticreeping code of radio is erased.


2. Push two dismantling keys (51) and Take the radio receiver (A2).
3. Wring out lock springs (shooter) and extend dismantling keys.
4. On the back party of the radio receiver mark wires an adhesive tape and remove them.

Installation

PERFORMANCE ORDER
1. In the serial car the antenna cable, and also the line to the antenna with remote control of its promotion is not established, they need to be carried out in addition.
2. Connect behind the wire radio receiver according to marking and according to the instruction of the manufacturer.
3. Insert with pressing the radio receiver into a console opening.
4. Connect a weight(s) wire to the plug of the rechargeable battery. Determine time on hours and program an anticreeping code for radio.

Instructions to additional installation of the radio receiver


Prevention

If the serial connecting wire is not applied, surely pay attention to that there were no loose uninsulated wires. Otherwise short circuit will lead to burn-out of a wire. In shops it is possible to get adapters for connection of the radio receiver.


Pay attention to that only the sets of elements which passed standard tests (throttles, condensers) were applied to suppression of hindrances (with the general permission to operation of the ABE vehicle). In trade especially for the Mercedes cars there are coordinated sets of elements for suppression of hindrances together with the installation guide.

Coordinate the radio receiver with the antenna. For this purpose adjust low-power mediumwave the transmitter approximately on 1400 kHz. If there is no transmitter, then it is possible to use the noise generator to control. Turn the small screw-driver the screw of coordination of the antenna (ahead at the left in the radio receiver case) until the best reception or the maximum level of noise is reached.


Prevention

At the same time turn the control screw at most only on 1/2 turns.