Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
- 13. Body
   13.2. Forward door
   13.3. Back door
   13.4. Handle of a forward door
   13.5. Handle of a back door
   13.6. Door lock
   13.7. Internal covering of doors
   13.8. Forward window regulator
   13.9. Glass of a forward window
   13:10. Back window regulator
   13:11. Glass of a forward door
   13:12. Window regulator engine
   13:13. Glove boxing
   13:14. Gear shifting handle sheeting
   13:15. Forward ashtray
   13:16. Average console
   13:17. Heating service panel
   13:18. Internal covering of the A-rack
   13:19. Internal covering of the S-rack
   13:20. Front seat
   13:21. Back seat
   + 13:22. Central lock
   13:23. External mirror / glass of a mirror
   13:24. A covering under the dashboard
   13:25. Front bumper
   13:26. Rear bumper
   13:27. Internal wing of the car
   13:28. Car wing
   13:29. Lattice Mercedes radiator / emblem
   13:30. Draft of a cowl of the engine
   13:31. A covering under a windshield
   13:32. The air supply device for heating of salon
   13:33. Catchment basin
   13:34. Paint and varnish covering
   13:35. Metal corrosion
   13:36. Automake-up
   13:37. What creaks?
   13:38. Hatch
+ 14. Electric equipment
+ 14.2. Electrical circuitries





13.8. Forward window regulator

Removal

PERFORMANCE ORDER
1. Remove an internal covering of a door.
2. Carefully remove the pressurizing film. Be careful: the film is easily torn.
3. Lower glass of a window as low as possible until the screw (2) appears in an assembly opening. (3 – the window regulator tire, 1 – glass.)
4. Unscrew the screw (2) in front on the window regulator tire.
5. Slightly raise glass behind and Take crackers from the window regulator tire.
6. Press glass up and insure it from loss by a plastic or wooden wedge.

7. Window regulator (4) приклепан. Drill 6 rivets (8) a drill 4, 8 mm. At the same time track that the drill did not enter an internal tin of a door. For a zaklepyvaniye pincers are necessary for secret rivets.
8. Extend a window regulator with the tire and take down. Take the power window together with the engine. Disconnect a window regulator wire.

Installation

PERFORMANCE ORDER
1. Establish a window regulator at a door and rivet by means of pincers for a secret klepka. If is not present at the disposal of pincers, then it is possible to fix a window regulator by screws and nuts. Cover screws before twisting with the protectant, for example, of Loctite 270 or Omnifit.
2. Carefully lower glass and enter together with crackers from the window regulator lever into a window regulator tire cut.
3. Insert the forward lever of a window regulator into the tire of the elevator and screw, without tightening. The screw (2) drags on only after the door window is adjusted.
4. Attach electric wires.
5. Adjust a door window.
6. Paste the pressurizing film so that there were no folds.
Prevention

Do not damage a film – it has to carry out sealing faultlessly.


7. Establish an internal covering of a door.