Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
- 12. Brake system
   12.2. Anti-blocking system – ABS
   12.3. The additional equipment – the ASR system
   12.4. Specifications of the brake system
   12.5. Overlays of front brake shoes
   + 12.6. Overlays of back disk brakes
   12.7. Support
   12.8. Forward brake disk
   12.9. Back brake disk
   12:10. Brake fluid
   12:11. Removal of air from the brake system
   12:12. Brake pipelines / hoses
   12:13. Replacement of brake highways
   12:14. Brake shoes of the parking brake
   12:15. Adjustment of the parking brake
   12:16. Stoplight switch
   12:17. Diagnostics of malfunctions of brakes
   + 12:18. Wheels and tires
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electrical circuitries





12.7. Support

GENERAL INFORMATION

Support of a forward wheel


Support of a back wheel

Removal

PERFORMANCE ORDER
1. Mark with paint the provision of wheels concerning a nave. Thanks to it the balanced wheel after removal can be put on the place that balancing was not broken. Release wheel bolts, without lifting the car, then put the car on supports and remove wheels.
2. Switch off ignition. Unscrew and get the sensor of speed of the ABS (L6/1) system.
3. Unscrew 2 bolts of fastening of a brake support of a back wheel (35) to the case of bearings of a wheel and remove it outside.
4. Suspend a support by means of a self-made hook to a body so that were not overwound and the brake hose and a wire of the sensor of wear of brake slips were not drawn.
5. If the support has to be removed completely, unscrew at first a brake hose (51) from a hydrowire, applying for this purpose an open double cap key of 9х11 mm. Then unscrew a brake hose from a support.
Prevention

Brake fluid will begin to flow. Close immediately openings caps that the tank did not become empty. After installation the brake system needs to be pumped over. In cars with the ASR traction control system pumping of brakes requires the special device used in specialized workshops. Collect the following brake fluid in specially intended capacity. Observe indications for the treatment of brake fluid (see subsection 12.10.).


6. Disconnect the sensor of wear of slips on the support socket. Unscrew the socket from a support.

Installation

PERFORMANCE ORDER
1. When replacing keep in mind: the brake mechanism on both wheels of one axis has to have identical pistons of the same manufacturer.
2. Forward brakes: put a support and tighten it to a nave two new самоконтрящимися bolts with m 115 N.' moment.
Prevention

If bolts go hard, clear a carving of the remains of fixing means by means of a tap of M 12х1,5.


3. Back brakes: put a support and fix two new самоконтрящимися by bolts on a nave with m 50 N.' moment, in cars with the ASR system – 70 N. m.
Prevention

If bolts go hard, clear a carving of the remains of fixing means by means of a tap of M 10.


4. If the brake hose was removed, screw it with m 15 N.' moment on a hydrowire. At installation the hose cannot be overwound. On an arm (52) the lock plate (60) with a dodecahedron is fixed. Insert a brake hose (51) into a lock plate so that it went freely at full turn of a wheel to the left and to the right, at compression and stretching of a spring of a suspension bracket. 4 – a hydrowire, 13 – the cap screw, 59 – an arm of a brake hose.
5. Grease an opening for the ABS system speed sensor with means of Molykote Longtherm 2. Check a ring of round section, if necessary – replace. Put the speed sensor, having tightened it a new bolt with an internal hexagon with m 20 N.' moment,
6. Connect a wire of the sensor of wear of slips to the socket on a support.
7. If the brake system opened, pump over brakes.
8. Put wheels so that the marking put before their removal coincided. Screw wheels. Remove the car from supports and tighten wheel bolts in a crosswise order with m 110 N.' moment.
Prevention

Vigorously repeatedly press on a brake pedal, you will not feel strong resistance yet. Thanks to it there is an adjustment of brake slips.


9. Check the level of brake fluid in a tank, if necessary add to the maximum mark.
Prevention

Carry out safety control:
      – whether brake hoses are tightened;
      – whether there is a brake hose in an arm;
      – whether pumping screws are tightened;
      – whether as it should be level of brake fluid

  At the working engine make tightness control. For this purpose press a brake pedal with effort from 200 to 300 N (20–30 kg) within about 10 seconds. The pedal should not move. Check tightness of all connections.


10. In conclusion make several braking on the quiet street.