Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. Engine
   3.1.4. Cars with the conditioner
   3.1.5. Lower cover of a motor compartment
   3.1.6. Covers of cast openings
   3.1.7. Natyazhitel of a chain
   + 3.1.8. Cover of a head of the block of cylinders
   + 3.1.9. Head of the block of cylinders
   - 3.1.10. Camshafts
      3.1.10.1.2. Control / adjustment of a basic position
      3.1.10.2. 6-cylinder engine
   3.1.11. Hydraulic dish-shaped pushers
   3.1.12. Maslootrazhatelny caps
   3.1.13. Valves
   3.1.14. The directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. Compression
   + 3.1.17. Maple belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. General comments
   3.1.20. Repair work without dismantle of the engine
   + 3.1.21. Capital repairs of the engine
   + 3.2. Diesel Engine (DE)
   3.2.3. Cars with the conditioner
   3.2.4. Lower cover of a motor compartment
   3.2.5. Covers of cast openings
   3.2.6. Natyazhitel of a chain
   + 3.2.7. Camshaft
   + 3.2.8. Head of the block of cylinders
   + 3.2.9. Maslootrazhatelny caps
   3.2.10. Cover of a head of the block of cylinders (2,2 / 2,5 l)
   3.2.11. Hydraulic dish-shaped pushers
   3.2.12. Valves
   3.2.13. The directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. Head of the block of cylinders and motor block
   3.2.16. Compression
   3.2.17. Maple ridge belt
   3.2.18. The pulling device of a maple ridge belt
   3.2.19. Diagnostics of malfunctions (DD)
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electrical circuitries






3.1.10.1.2. Control / adjustment of a basic position

GENERAL INFORMATION

Camshafts

1. A wrench (for turn of camshafts)
73. Chain of management
75. Gear wheel of the inlet camshaft
76. Gear wheel of the final camshaft
77. Final camshaft
78. Inlet camshaft
79. Cover of the bearing of camshafts
79a. Fastening bolt

Control

PERFORMANCE ORDER
1. Install the cylinder 1 on 20 ° after VMT. Instruction: in this situation (20 ° after VMT) it is possible to turn camshafts at the removed managing director of a chain without contact of valves with the piston basis.
2. Uncover a head of the block of cylinders.
3. Fix camshafts. For this purpose enter the fixing pins (01) through an opening (shooter) in a cover of the bearing of camshafts 1 and 6 into an opening of a flange of camshafts. If it is impossible to insert the fixing pins, adjust basic provisions of camshafts.

Prevention

For the 2,2 l engine turn the regulator of cam-shafts about a gear wheel of the inlet camshaft (75) in situation "spat" (late) against the stop in the direction of rotation of the camshaft (shooter).



Adjustment

PERFORMANCE ORDER
1. The cylinder 1 costs on 20 ° after VMT of ignition and the head of the block of cylinders is uncovered.
2. Remove forward covers.
3. Remove a natyazhitel of a chain.
4. Unscrew a gear wheel of the final camshaft a wrench with T40 nozzle, holding a cam-shaft at a hexagon. Remove a camshaft gear wheel.
5. Remove the operating chain from a gear wheel of the final camshaft.
6. Turn camshafts a wrench until it is possible to enter the fixing pins.
7. Establish a chain wheel and impose a chain.
8. Establish a natyazhitel of a chain.
9. Double-check a basic position of camshafts. If necessary repeat adjustment.
10. Establish forward covers of camshafts.
11. Establish a cover of a head of the block of cylinders.