Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. Engine
   3.1.4. Cars with the conditioner
   3.1.5. Lower cover of a motor compartment
   3.1.6. Covers of cast openings
   3.1.7. Natyazhitel of a chain
   + 3.1.8. Cover of a head of the block of cylinders
   + 3.1.9. Head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic dish-shaped pushers
   3.1.12. Maslootrazhatelny caps
   3.1.13. Valves
   3.1.14. The directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. Compression
   + 3.1.17. Maple belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. General comments
   3.1.20. Repair work without dismantle of the engine
   + 3.1.21. Capital repairs of the engine
   + 3.2. Diesel Engine (DE)
   3.2.3. Cars with the conditioner
   3.2.4. Lower cover of a motor compartment
   3.2.5. Covers of cast openings
   3.2.6. Natyazhitel of a chain
   + 3.2.7. Camshaft
   + 3.2.8. Head of the block of cylinders
   + 3.2.9. Maslootrazhatelny caps
   3.2.10. Cover of a head of the block of cylinders (2,2 / 2,5 l)
   3.2.11. Hydraulic dish-shaped pushers
   3.2.12. Valves
   3.2.13. The directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. Head of the block of cylinders and motor block
   3.2.16. Compression
   3.2.17. Maple ridge belt
   3.2.18. The pulling device of a maple ridge belt
   3.2.19. Diagnostics of malfunctions (DD)
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electrical circuitries





3.1.7. Natyazhitel of a chain

GENERAL INFORMATION

Prevention

If the natyazhitel is weakened on a hexagon, then it should be removed, otherwise at screwing up the operating chain will be excessively tightened.


Removal

4-CYLINDER ENGINE


PERFORMANCE ORDER
1. Remove the hydraulic coupling of the fan.
2. Uncover a head of the block of cylinders.
3. Remove a fan casing.
4. Install the engine on 20 ° below VMT of ignition of the first cylinder. For this purpose transfer the transmission to the provision of idling and tighten the parking brake. Turn a bent shaft by means of a wrench with SW27 nozzle at the central bolt of a belt pulley of a bent shaft in the direction of rotation of the engine, i.e. clockwise, before coincidence of markings. Length of a nozzle of a wrench has to be more than 42 mm.
5. Insure a final cam-shaft from turn. For this purpose enter a suitable core (Mercedes-N 111589011500) into an opening of a flange of a cam-shaft (78) through an opening in a cam-shaft bearing cover. If the chain is removed, then in the same way record an inlet cam-shaft.

Prevention

If you do not insert the fixing pin (shooter), adjust a basic position of a cam-shaft.


6. Close the generator a film or a rag.

6-CYLINDER ENGINE

PERFORMANCE ORDER
7. Take off maple a ridge belt.
8. If necessary weaken and remove the air pump from above of a natyazhitel of a chain.

ALL ENGINES


PERFORMANCE ORDER
9. Weaken a screw stopper (1), having turned on one turn, using a face key of SW10.
10. Unscrew a natyazhitel of a chain in a complex with a detail (14) and remove.
11. Unscrew a screw stopper (1) with a sealing ring (5). Take a spring of compression (8) together with a pin (7).
12. Push out press a finger (10) with a fiksatorny spring (9) back.
13. Separately carefully clean details fuel and check for further suitability to use (risks, a raid). Replace the damaged details, in case of need in a set replace a natyazhitel of a chain.

Installation

PERFORMANCE ORDER
1. Fasten to the motor block the case of a natyazhitel of a chain (14) with a new sealing ring (15). The inhaling moment for the 4-cylinder engine – 80 N. of m, for 6-cylinder – 50 N. of m.
2. Collect details (7-10) as before their dismantling, and insert in the mounted natyazhitel of a chain.
3. Twirl a screw stopper (1) with the new condensing ring (5) with m 40 N.' moment, at the same time the spring contracts.

4-CYLINDER ENGINE
Prevention

Take the stopping core from a cam-shaft flange.


PERFORMANCE ORDER
4. Establish a cover of a head of the block of cylinders.
5. Remove the closing film from the generator.
6. Install the hydraulic coupling of the fan.
7. Start the engine and check tightness of a natyazhitel of a chain.

6-CYLINDER ENGINE

PERFORMANCE ORDER
4. Fix the air pump.
5. Put on maple a ridge belt.
6. Start the engine and check tightness of a natyazhitel of a chain.