Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Lubrication system
- 5. Cooling system
   - 5.2. Cooling liquid
      5.2.2. Diesel engine
      5.2.3. Cars with the conditioner
   5.3. Antifreeze for a radiator
   5.4. Temperature regulator of cooling liquid (thermostat)
   5.5. Check of the cooling system
   5.6. Hydraulic coupling of the fan
   5.7. Pump of system of liquid cooling
   5.8. Radiator
   5.9. Fan casing
   5.10. Diagnostics of malfunctions of the cooling system
   5.11. Diagnostics of malfunctions of system of indication of level of liquid
   5.12. Engine overheat
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electrical circuitries





5.2.2. Diesel engine

GENERAL INFORMATION

1. Compensation tank
1a. The silicate reserve (preventing aluminum corrosion)
2. A radiator with a horizontal stream of cooling liquid
3. Regulator of cooling liquid (thermostat)
4. Water pump системыв liquid cooling
6. Heat exchanger of system of heating
7. Ventilating (blowing-off) line
A31. Block of forcing of system of heating
A31u1. Double клапаг at the left
A31u2. Double клапаг on the right
M. Engine
S. Capacity for an obmyv of glasses (the warmed-up cooling liquid)

PERFORMANCE ORDER
1. Remove the lower cover of a motor compartment.
2. Put on a hose the drain union of a radiator. In the drawing – the 2,0 l engine.
3. Put on a hose with an internal diameter of 12 mm the drain union of a radiator. In the drawing – the 2,5 l engine.
4. Install a pure reception vessel under a radiator, enter into it a hose and open a carving stopper of a drain opening.

Discharge

PERFORMANCE ORDER
1. 2,0 l engine: put a pure vessel under the engine and turn out a carving stopper (12) of a drain opening on the block of cylinders of the engine.
2. 2,2 / 2,5 l engines: put on a hose with an internal diameter of 14 mm a carving stopper (4) of a drain opening on the block of cylinders of the engine (shooter).
3. Substitute a pure reception vessel under the engine, enter into it a hose and only weaken a carving stopper (4) of a drain opening, without unscrewing it.
4. Completely lower cooling liquid.
5. Tighten a carving stopper of a drain opening on the block of cylinders of the engine with m 30 N.' moment.
6. Twist with the moment 1,5–2,0 N. of m (manually) a carving stopper of a drain opening on a radiator.
7. If it is got, then remove a drain hose.
8. Establish the lower cover of a motor compartment.

Gulf

PERFORMANCE ORDER
1. Check the content of antifreeze in cooling liquid.
2. Fill cooling liquid through a bulk branch pipe of a compensation tank (2) to a mark (shooter). At the vehicles having a black top part of a tank prior to the beginning of a black part.

Prevention

That cooling liquid quickly got from a compensation tank to a radiator, and, respectively, to the engine, it is possible to squeeze out for filling with cooling liquid a bulk hose down.

3. Connect a weight wire to the rechargeable battery.
4. Leave the engine to get warm until the regulator of temperature of cooling liquid is opened (temperature about 100 °C). At the same time establish at full capacity heating and pushes press an accelerator pedal.
Prevention

At a temperature of cooling liquid of 60-70 °C close a compensation tank.


5. Check tightness of the cooling system – accession of hoses, and also carving traffic jams of drain openings.
6. Expose time on hours.
7. Enter an anticreeping code of radio.