Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
- 4. Lubrication system
   4.2. Specification of engine oil
   4.3. Scope viscosity oils / class
   4.4. Oil consumption
   4.5. Contour of circulation of oil (DD)
   4.6. Oil reducing valve
   - 4.7. Oil pallet
      4.7.2. Diesel engine (2,0 l)
      4.7.3. Diesel engine (2,2 / 2,5 l)
   4.8. Oil level indicator
   4.9. The heat exchanger oil - / cooling liquid
   4.10. Diagnostics of malfunctions in an oil circulation contour
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electrical circuitries





4.7. Oil pallet

4.7.1. Petrol engine

GENERAL INFORMATION

 
1. Radiator clip
2. Fan case clip
3. Fan case
4. Radiator
5. Engine electrical wiring covering
11. Bolts of a forward support of the engine
12. Bolts of a back support of the engine
16. Cover
S43. Shtekker of the oil level sensor
56. Oil pallet
56a. Sealing laying of the pallet

Bolts of fastening of the oil pallet


 
6. Bolt of M 6 x 20 9 mm
7. Bolt of M 6 x 35 9 mm
8. Bolt of M 6 x 85 9 mm
9. Bolt of M 8 x 40 21 mm
10. Bolt of M 10 x 40 40 mm
56. Oil pallet

Removal

PERFORMANCE ORDER
1. Remove the lower cover of a motor compartment.
2. Remove the stabilizer.
3. Lower engine oil.
4. Uncover (16).
5. Remove clips (2).
6. Raise the case of the fan and put on the fan.
7. Disconnect clips (1) from a radiator.
8. Weaken the top oil pipeline (shooter) on the pump of the amplifier of steering and turn down.
9. Shoot the cable film for an engine electrical wiring.
10. Remove an engine electrical wiring covering from a dividing partition between units.
11. Disconnect a forward exhaust pipe from a final collector.
12. Unscrew a support of the holder of an exhaust pipe from the transmission.
13. Disconnect the oil level sensor plug.
14. Unscrew bolts of a forward support of the engine.
15. Unscrew bolts of fastening of a back support of the engine.
16. Hook on the engine for forward and back eyes.
17. Raise the engine as much as possible horizontally.
18. Unscrew bolts of fastening (6/7/8/9/10) of the oil pallet and remove the oil pallet (56) (see rice. Bolts of fastening of the oil pallet).
19. Carefully clear the sealing surface of the oil pallet and a case of a bent shaft.

Installation

PERFORMANCE ORDER
1. Install the oil pallet with new sealing laying, level its rather back surface prileganiye to the check point and evenly manually fix by bolts. Then alternately twirl bolts with the ordered moment (see rice. Bolts of fastening of the oil pallet).
Prevention

If the oil pallet is not leveled concerning the transmission, then subsequently it will lead to noise.


2. Lower the engine.
3. Insert bolts of fastening of a forward support of the engine and screw up them manually.
4. Screw up bolts of a forward support of the engine with m 40 N.' moment.
5. Put on the oil level sensor plug.
6. Attach a forward exhaust pipe to a final collector, a support of the holder of an exhaust pipe at the check point.
7. Establish an engine electrical wiring covering on the partition dividing units.
8. Fix an engine electrical wiring at the right wheel.
9. Turn an oil pipeline of the pump of the amplifier of steering up and fix.
10. Put on clips a radiator.
11. Install the case of the fan and fix by clips.
12. Establish a cover (16).
13. Install the stabilizer.
14. Establish the lower cover of a motor compartment.
15. Fill in engine oil.
16. Warm up the engine and check tightness of the oil pallet.