Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
   14.1.2. Measuring devices
   14.1.3. Technology of measurements
   14.1.4. Checks of electric equipment
   14.1.5. Sound signal
   14.1.6. Replacements of safety locks
   + 14.1.7. Rechargeable battery
   + 14.1.8. Generator
   + 14.1.9. Starter
   14.1.10. Traction relay
   + 14.1.11. System of lighting
   14.1.12. Devices
   14.1.13. Dashboard
   14.1.14. Glow lamps on the dashboard
   14.1.15. Light switch
   14.1.16. Radio receiver
   + 14.1.17. Antenna
   14.1.18. Loudspeakers
   - 14.1.19. Rubber brushes of screen wipers
      14.1.19.1. Diagnostics of malfunctions of brushes of screen wipers
   14.1.20. Windscreen washer jets
   14.1.21. The washing nozzles of headlights
   14.1.22. Screen wiper and its engine
   14.1.23. Protect the car
   14.1.24. Anticreeping "immunodeficiency"
   14.1.25. Why headlights grow dull
   14.1.26. Galogenka
+ 14.2. Electrical circuitries





14.1.19. Rubber brushes of screen wipers

GENERAL INFORMATION

Rubber brushes of a screen wiper should be replaced at bad quality of purification of glasses. In trade separate rubber brushes of a screen wiper are offered as complete brushes of a screen wiper (a rubber brush with the holder), and. If only the rubber brush is replaced, pay attention to that her holder was not bent.

The rubber brush is entered in two metal the fixing guides (1) which at removal have to understand separately.

Removal


Prevention

At work on screen wipers Take the ignition key. When moving the lever of a brush or the lever mechanism of a screen wiper, since position "1" of the ignition key, automatic equipment of return of brushes to a starting position can turn on. I.e. the screen wiper works in the single mode until it is in a starting position. There is a danger of a trauma!


PERFORMANCE ORDER
1. Raise the screen wiper brush lever, without fixing it.
2. Press a plastic clip on a corrugated detail (1) down and displace a screen wiper brush (2) from a hook on the screen wiper brush lever down.
3. The narrow screw-driver (2) remove from the closed party a rubber brush from both steel guides (2) back and carefully extend a rubber brush from guides.
4. Unhook a rubber brush (3) from collars (4) on a screen wiper.

Installation

PERFORMANCE ORDER
1. Freely lay a rubber brush not in the fixing guides, and in screen wiper clips.
2. The open profile party enter both guides into a rubber brush so that flutes of guides looked towards rubber and were recorded in groove ledges. The bend of guides has to look in the direction of glass.
3. Spring latches enter a clamp flute easier if its previously forward end is mown by a file and is greased with soap water (detergent).
4. Grease a rubber brush on the closed party with soap water that it slid in collars better.
5. Both steel guides and a rubber brush clamp passatizham and hang in collars of the screen wiper.
6. Get a screen wiper brush so that it was between both directing pins on the screen wiper lever.
Prevention

If the new brush of a screen wiper is established, press plastic clips on corrugated details down.


7. Push a screen wiper brush in hooks of its lever, clamp plastic clips and by that record a screen wiper brush.
8. Press the screen wiper brush lever. At the same time pay attention to that the rubber brush adjoined to glass everywhere.
9. Include a screen wiper. The sector of cleaning has to be cleared easily.
Prevention

The rubber sponge of a brush of a screen wiper at change of the direction of the movement has to be bent (to overturn). If it does not occur, carefully bend the screen wiper brush lever so that its end settled down parallel to glass.